Lockouts · Hamilton
Break-In Damage Lock Repair
Police have come and gone, the occurrence number is on a sticky note, and you are standing in a cold hallway looking at a splintered frame, wondering how the house gets locked before everyone tries to sleep.
In plain words
A failed break-in is still a repair. When a lock holds against a pry bar or a kick, the force goes somewhere: a strike plate bends, screws loosen, the door edge takes a gouge, the deadbolt binds where the bolt met the strike under load. Left alone, that door locks a little worse each week and the next attempt starts from where the first one finished. The visit checks every part that took the strain, replaces what bent, reinforces the strike and hinges with long screws and confirms the bolt throws cleanly again. It is also the moment to add what would have made the attempt pointless from the start.
How the visit goesThe back door looks closed until you touch it. The edge is crushed where a bar went in, the latch is bent sideways, and the door swings free with a gentle push no matter how you turn the key.
Break-In Damage Lock Repair
How the visit goes
The other openings
The attacked door was chosen for a reason, and the locksmith walks the rest of the property to see whether the same reason applies elsewhere. A back door with a knob lock and no deadbolt, a garage man-door on a light latch, a basement walkout hidden from the street, a sliding door with no anti-lift blocks or a side gate that is never locked are all noted. The walk takes a few minutes and lets you decide, with the whole picture in view, whether the repair stops at the forced door or brings the weaker openings up to the same standard while the tools are out.
Strengthening the door edge and hinges
Where a pry bar crushed the edge or the wood split around the lock bore, a wrap-around reinforcer is fitted: a steel channel that sleeves the door edge at the lock, ties the two faces together and gives the bolt and latch a solid seat. On the hinge side, the short factory screws are swapped for three-inch screws that reach the framing, and a bent hinge is replaced. Doors that were kicked hard sometimes need a hinge reinforcement plate across the jamb to spread the load. With both edges strengthened, the door no longer has a soft side, and a future kick meets steel and stud at every point that matters.
New keys and a clean slate
If keys were taken, you now hold a set that fits locks nobody else can open. The cylinders were pinned to a fresh combination and the new keys were cut from that pinning, tested in each door and counted into your hand. It is worth deciding on the spot who gets one and where the spare lives, which is no longer a hook by the door. Garage remotes have been erased and re-paired, and you have been reminded to change alarm codes and any code written on paper that was disturbed. The stolen ring is now a handful of metal that turns nothing.
Break-In Damage Lock Repair
In the van
Rekeying pins and key blanks
Plywood and cleats for boarding
Anti-lift blocks and foot bolt
Replacement cylinder or core
Grade 1 deadbolt with one-inch throw
Break-In Damage Lock Repair
What affects the quote
How many parts were damaged
One broken cylinder on a sound frame is a small repair. A torn strike, a split jamb, a crushed door edge and bent hinges together are a longer visit with more hardware, and the quote follows the count.
Grade of the replacement deadbolt
A residential deadbolt with a one-inch throw and hardened insert, a heavier commercial-grade unit and a keypad or smart deadbolt sit at different points, and the quote names the one you choose.
Number of cylinders rekeyed
Every lock a taken key fits is rekeyed individually, so a house with four exterior doors, a mailbox and two padlocks is more work than one front door. Bringing them all onto a single key is part of the count.
What to have ready
- Is there glass beside the door or in it?
- Are there other doors or a garage entry on the same key?
- Were any keys, garage remotes or alarm codes taken?
Break-In Damage Lock Repair: questions
QuestionsThe intruder pried open our sliding patio door. Can it be made secure?
Yes. The panel goes back on its track and the broken latch is replaced, then the weaknesses a slider is born with are addressed: anti-lift blocks in the upper channel so the panel cannot be raised off its rollers, a foot bolt or pin lock through the frame at the bottom, and an auxiliary keyed lock if the latch alone is flimsy. A bowed frame may need a door installer, with the opening secured until they come.
I rent. Who arranges the repair, and can I change the lock myself?
Tell your landlord or property manager as soon as the police have been called; provincial tenancy law makes the landlord responsible for repairs to the unit, and most will arrange the locksmith. A tenant may not change locks without the landlord's agreement, and a landlord who changes them must give the tenant keys, so the visit is coordinated between you. If you arrange securing yourself in an emergency, keep the receipt and the record of what was done for both sides.
The intruder found our spare keys. What should be rekeyed?
Everything those keys fit. That usually means the front, back and side doors, the garage man-door, the mailbox and any padlocks, and in a rental the suite door with the landlord's involvement. Rekeying changes a serviceable cylinder to answer to a new key, and a cylinder that cannot be rekeyed is replaced instead. Doing every affected opening in one visit, keyed alike where the cylinders are compatible, means no forgotten door still answers to the stolen ring.
Related services
- Business Lockout ServiceA cook stepped into the alley with the recycling and the rear door swung shut behind him.
- Broken Key ExtractionYou were locking up on the way out when the key broke in the lock.
- Seized & Jammed Lock OpeningThe key slides all the way in, exactly as it has for years, and then refuses to turn in either direction.